MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part. INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr
Maximale Bewegungsfreiheit und maximaler Style. Das Nike Training Hyper Tank Women eignet sich für verschiedene Trainingsarten im Fitnessstudio und überall sonst. Es hat weite Armausschnitte und Schlitze an den Seiten, damit Du Dich beim Workout frei bewegen kannst.Größenauswahl-Hilfe: Model mit 170 cm Größe und 60 kg Gewicht trägt Größe SGrößenauswahl-Hilfe: Model mit 161 cm Größe und 72 kg Gewicht trägt Größe LEigenschaften: Material: 75% Polyester (recycelt) / 13% Baumwolle aus biologischem Anbau / 12% ViskosePassform - Fit: Locker geschnittenGrößenflag: Fällt normal aus Pflegehinweise: Maschinenwäsche, keinen Weichspüler verwenden Curved Schnitt: Abgerundeter Saum vorne und hinten für einen figurschmeichelnden Look und SchutzDas Nike Dry-Material sorgt für Trockenheit, Tragekomfort und mehr Fokus: Dri-FIT-Material sorgt für trockenen Tragekomfort: Es leitet Feuchtigkeit vom Körper weg und hält ihn trockenDri-FIT-Technologie sorgt für trockenen TragekomfortStandardpassform für ein relaxtes, unkompliziertes TragegefühlDank der weiten Armausschnitte und Schlitze an den Seiten macht das Tanktop alle Bewegungen mitDas Design mit gekreuzten, elastischen Trägern am Rücken besticht mit einem Schachbrettprint mit integriertem NIKE Schriftzug und Swoosh LogosDer Rundhalsausschnitt sorgt für einen schmeichelnden LookSwoosh Logo als Outline vorn aufgedruckt
Already a legend in its time, the SRAM RED crankset is now available with refreshed graphics to complement our new SRAM RED eTap componentry. The SRAM RED crankset features a completely hollow construction all the way to the spider. Its hidden bolt pattern makes better use of carbon fibre to further improve stiffness and shed weight. As always, for seamless, flawless performance and Yaw compatibility, pair this crank with X-GlideR chainrings.TechnologyExogramThe new Hollow Carbon Construction starts in the crank arm and extends into the cranks’ spider. It maximizes the stiffness to weight ratio.X-GlideR ChainringsThe chainrings are designed for an optimized shifting performance with the Yaw front derailleur. The stiffer rings (5mm 7075-T6 aluminium CNC-machined) feature upshift rivets with an advanced design adopted from SRAM XX. CNC machining allows for precision control of each tooth shape, ramp, and nearly every shifting feature of the chainring. Chainrings, chain, and front derailleur are designed as a single integrated system for optimized performance.Specifications for SRAM RED Crankset •ARM MATERIAL: Carbon •CHAINRING MATERIAL: Machined alloy •WEIGHT: 557g (BB30 172.5mm 53x39 BB not included) •AVAILABLE ARM LENGTHS: 165mm, 167.5mm, 170mm, 172.5mm, 175mm, 177.5mm •AVAILABLE RATIOS: 53/39, 52/36, 50/34, 46/36 •COMPATIBILITY: SRAM RED & SRAM Force Yaw Front Derailleur, SRAM RED 22 & PC1170 chains •FINISH: Carbon •TECHNOLOGY HIGHLIGHT(S): Exogram Hollow Crank Arm & Spider w/ X-GlideR Chainrings / Hidden Bolt Spider Tab •OPTIONS: GXP, PressFit, BB30, PressFit 30 availability
Universal bracket for attaching the Tom Tom Rider (40, 400, 410, II, 42, 420, 450) to tubular handlebars or the mirror arm Compatible with tubular handlebars with diameters between 8 and 35 mm Important note: Without TomTom Rider docking station!
